using firmware 3.1.10 (GWd)
When I first switched from Engin to VoIPer, I couldn’t get my SPA-3000 to work at all. Below you will find all the settings for the Line 1 tab of the SPA-3000 so that you can configure your SPA-3000 to work with VoIPer.
Before you Start
Before you start, make sure you have all the relevant settings for your VoIPer Plan. You will find your setting information from the Engin website. First login to Engin using your phone number and password sent to you by Engin when you first signed up.
Next, click on the summary tab at the top of the page, and you will see your connection details on the right hand side of the screen (something like this).
You need to enter the subscriber information you get from the Engin website in your SPA-3000. Log on to your SPA\Advanced\Admin and go the Line 1 Tab (if you don’t know how to do this, first have a look at the SPA-3000 setup guide.
Towards the bottom of the line 1 page, find the Proxy and Registration
section
Enter your subscriber information in the area provided.
The following section is for your subscriber information. Enter the information you got from the Engin website as outlined above.
Settings
In case you have problems like I did, here are all the settings for the Line 1 tab. Some of these are optional, but some are essential. If you set it up like this, you should be able to get it running. After that, you are free to experiment to see what happens.
The major settings to check (on the line1 tab) are:
1) Line Enable: Yes
2) Outbound proxy should be blank and Use outbound set to no.
3) User ID and Auth ID should both be set to your phone number including
area code. Use Auth ID set to yes.
I have also provided a full copy of my config file here: MattsSipuraSPA3000Config.zip
Page : Line 1
Category : Line 1
Line Enable: yes
Category : Streaming Audio Server (SAS)
SAS Enable: no
SAS DLG Refresh Intvl: 30
SAS Inbound RTP Sink:
Category : NAT Settings
NAT Mapping Enable: no
NAT Keep Alive Enable: no
NAT Keep Alive Msg: $NOTIFY
NAT Keep Alive Dest: $NOTIFY
Category : Network Settings
SIP TOS/DiffServ Value: 0x68
Network Jitter Level: medium
RTP TOS/DiffServ Value: 0xb8
Jitter Buffer Adjustment: up and down
Category : SIP Settings
SIP Port: 5060
SIP 100REL Enable: no
EXT SIP Port:
Auth Resync-Reboot: yes
SIP Proxy-Require:
SIP Remote-Party-ID: no
SIP GUID: no
SIP Debug Option: none
RTP Log Intvl: 0
Restrict Source IP: no
Referor Bye Delay: 4
Refer Target Bye Delay: 0
Referee Bye Delay: 0
Refer-To Target Contact: yes
Sticky 183: no
Category : Call Feature Settings
Blind Attn-Xfer Enable: no
MOH Server:
Xfer When Hangup Conf: yes
Category : Proxy and Registration
Proxy: byo.engin.com.au
Use Outbound Proxy: yes
Outbound Proxy: byo.engin.com.au
Use OB Proxy In Dialog: yes
Register: yes
Make Call Without Reg: no
Register Expires: 900
Ans Call Without Reg: no
Use DNS SRV: no
DNS SRV Auto Prefix: no
Proxy Fallback Intvl: 900
Proxy Redundancy Method: Normal
Voice Mail Server:
Mailbox Subscribe Expires:
Category : Subscriber Information
Display Name: ENTER YOUR NAME HERE
User ID: 02xxxxxxxx (your VoIPer phone number incl area code)
Password: *
Use Auth ID: yes
Auth ID: 02xxxxxxxx (your VoIPer phone number incl area code)
Mini Certificate:
SRTP Private Key:
Category : Supplementary Service Subscription
Call Waiting Serv: no
Block CID Serv: no
Block ANC Serv: yes
Dist Ring Serv: no
Cfwd All Serv: yes
Cfwd Busy Serv: yes
Cfwd No Ans Serv: yes
Cfwd Sel Serv: yes
Cfwd Last Serv: yes
Block Last Serv: yes
Accept Last Serv: yes
DND Serv: yes
CID Serv: yes
CWCID Serv: yes
Call Return Serv: yes
Call Redial Serv: yes
Call Back Serv: yes
Three Way Call Serv: yes
Three Way Conf Serv: yes
Attn Transfer Serv: yes
Unattn Transfer Serv: yes
MWI Serv: yes
VMWI Serv: yes
Speed Dial Serv: yes
Secure Call Serv: yes
Referral Serv: yes
Feature Dial Serv: yes
Service Announcement Serv: no
Category : Audio Configuration
Preferred Codec: G729a
Silence Supp Enable: no
Use Pref Codec Only: no
Silence Threshold: medium
G729a Enable: yes
Echo Canc Enable: yes
G723 Enable: yes
Echo Canc Adapt Enable: yes
G726-16 Enable: yes
Echo Supp Enable: yes
G726-24 Enable: yes
FAX CED Detect Enable: yes
G726-32 Enable: yes
FAX CNG Detect Enable: yes
G726-40 Enable: yes
FAX Passthru Codec: G711a
DTMF Process INFO: yes
FAX Codec Symmetric: yes
DTMF Process AVT: yes
FAX Passthru Method: NSE
DTMF Tx Method: InBand
FAX Process NSE: yes
Hook Flash Tx Method: None
FAX Disable ECAN: no
Release Unused Codec: yes
Symmetric RTP: yes
Category : Gateway Accounts
Gateway 1:
GW1 NAT Mapping Enable: no
GW1 Auth ID:
GW1 Password:
Gateway 2:
GW2 NAT Mapping Enable: no
GW2 Auth ID:
GW2 Password:
Gateway 3:
GW3 NAT Mapping Enable: no
GW3 Auth ID:
GW3 Password:
Gateway 4:
GW4 NAT Mapping Enable: no
GW4 Auth ID:
GW4 Password:
Category : VoIP Fallback To PSTN
Auto PSTN Fallback: yes
Category : Dial Plan
Dial Plan:
(000S0<:@gw0>|*xx|xx.|<#9:>xx.<:@gw0>|1[38]00xxxxxxS0<:@gw0>|190xxxxxxx!|13xxxxS0<:@gw0>)
Enable IP Dialing: no
Emergency Number:
Category : FXS Port Polarity Configuration
Idle Polarity: Forward
Caller Conn Polarity: Forward
Callee Conn Polarity: Forward
